Xhorse Mini VCI FW2.0.4 J2534 cable vs. Clone Mini VCI FW 1.4.0 cable If you would want to reset immo, or make customization to cars, need at least 2.0.4 FW with 2.0.4 FW there is change in PCB, as it support VPW, and has extra security chip on the other hand, all these simple clones with 1.4.0 FW support only CAN. Mini-vci J2534 Driver.
- Normally i install the MINI VCI FOR TOYOTA TIS Techstream on windows xp computer, but now i have changed my computer system to win 7 64bit, so it is not easy to find another xp computer. Last month, i read in forum, it can be installed on 64bit win7/win8.
- Cheapest MINI VCI J2534 Single USB Cable Supports Toyota TIS Techstream V14.20.019 OEM Diagnostic Software,free shipping on obdii365.com. Windows XP/windows7/8/10.
- Quick note on techstream 10.x with windows 7 or greater x64 with the 1.4.1 (and possibly the 2.0.1) Mini VCI cable. I was having absolute fits trying to get the driver recognized. Turns out the cable was being recognized as a Broadcom Bluetooth 3.0 Chip.
- Jun 06, 2019 Mini VCI J2534 single cable with Toyota/Lexus Techstream software download, technical support and feedback. Windows 7 32 bit. Toyota Teschstream 14.10.028 has been tested OK with: Mini VCI cables (SV46-D. Install Mini VCI driver for Toyota TIS, press Next. Ready to install. Finish driver installation. Step 3: Crack Techstream.
Just received Techstream cable last night and installed the software on my 64 bit computer. Installation was not plug and play, but it is quite doable.
Since I am expecting to use Techstream quite a bit, I thought I would start a thread. For future Techstream users, here are the instructions I used to get the software connected to my vehicle for the 64 bit application:
TIS Techstream V10 Setup Instruction ( !!! for 64 bit system !!! ) :
1. copy ” Program Files (x86) ” folder to drive C: , tick ” replace all current items ”
2. plug the Mini VCI cable into USB
3. Open the Device Manager and locate two failing devices in the list. Both will appear with yellow icon (usually under ”Other”), indicating that Windows failed to install drivers for them. Now, right click each failing device, select Install Driver, then ”Browse my Computer” and locate to “C:Program Files (x86)XHorse ElectronicsMVCI Driver for TOYOTA TIS” (enable the ”include subfolders” flag). Click ”Next” and wait until drivers are installed.
You should now see two new devices: ”Universal Serial Bus ControllersUSB Serial Converte” and ”Ports (COM & LPT)USB Serial Port (COMx)”.
4. Run the FirmwareUpdateTool.exe from the “C:Program Files (x86)XHorse ElectronicsMVCI Driver for TOYOTA TIS”. Click ”Device Info”, You should see the ”Device connected” screen.
5. Now install Techstream software using “Techstream_Setup_V10.10.018.exe” on our software CD
6. Software Registration: copy the two *.ini files in ”Registration” folder to “C:Program Files (x86)Toyota DiagnosticsTechstreamEnv
* Attention: It’s C:Program Files (x86) not C:Program Files , BIG DIFFERENCE !!!
* Attention: It’s C:Program Files (x86) not C:Program Files , BIG DIFFERENCE !!!
7. Registry Hack: Run the mvci-64bit.reg file to modify the registry for Techstream to recognize MINI-VCI under Windows x64
8. Run Techstream software. Go to Setup | VIM Select menu and select the ”XHorse – MVCI”
11. Connect Mini VCI cable to your car‘s OBDII interface, turn ignition on, then click ”Connect to Vehicle” in Techstream. Wait. Then wait again. If everything works, you will be prompted to confirm car year/model after which you’ll get to the diagnostic interface.
* Important Note:
1. DO NOT change the “User Type” when you will run your TIS Techstream for 1st time! LEAVE IT with the Default option! “Official” Dealer/Repairer with other words…
2. in [ VIM Select ] option, please select the [ Xhorse – MVCI ], not [ TIS Techstream VIM ]
3. If you get the following reminder while using the program:
—————————————————————-
Register Techstream Software (S314-03)
Network connection is unavailable. A network connection is required to use Techstream software.
You can only connect 29 more times without a network connection before software registration is required.
————————————————————--
You can reset that as following steps:
Go to C:Program FilesToyota DiagnosticsTechstreamEnv and find ”IT3usercustom.ini” file and look for ”Connectioncount=1” or what ever number of times you tried and just delete ”connectioncount=1”. Click save and you should be reseted back to 30
1. DO NOT change the “User Type” when you will run your TIS Techstream for 1st time! LEAVE IT with the Default option! “Official” Dealer/Repairer with other words…
2. in [ VIM Select ] option, please select the [ Xhorse – MVCI ], not [ TIS Techstream VIM ]
3. If you get the following reminder while using the program:
—————————————————————-
Register Techstream Software (S314-03)
Network connection is unavailable. A network connection is required to use Techstream software.
You can only connect 29 more times without a network connection before software registration is required.
————————————————————--
You can reset that as following steps:
Go to C:Program FilesToyota DiagnosticsTechstreamEnv and find ”IT3usercustom.ini” file and look for ”Connectioncount=1” or what ever number of times you tried and just delete ”connectioncount=1”. Click save and you should be reseted back to 30
who like this article also viewed:
Just received Techstream cable last night and installed the software on my 64 bit computer. Installation was not plug and play, but it is quite doable.
Since I am expecting to use Techstream quite a bit, I thought I would start a thread. For future Techstream users, here are the instructions I used to get the software connected to my vehicle for the 64 bit application:
TIS Techstream V10 Setup Instruction ( !!! for 64 bit system !!! ) :
1. copy ” Program Files (x86) ” folder to drive C: , tick ” replace all current items ”
2. plug the Mini VCI cable into USB
3. Open the Device Manager and locate two failing devices in the list. Both will appear with yellow icon (usually under ”Other”), indicating that Windows failed to install drivers for them. Now, right click each failing device, select Install Driver, then ”Browse my Computer” and locate to “C:Program Files (x86)XHorse ElectronicsMVCI Driver for TOYOTA TIS” (enable the ”include subfolders” flag). Click ”Next” and wait until drivers are installed.
You should now see two new devices: ”Universal Serial Bus ControllersUSB Serial Converte” and ”Ports (COM & LPT)USB Serial Port (COMx)”.
4. Run the FirmwareUpdateTool.exe from the “C:Program Files (x86)XHorse ElectronicsMVCI Driver for TOYOTA TIS”. Click ”Device Info”, You should see the ”Device connected” screen.
5. Now install Techstream software using “Techstream_Setup_V10.10.018.exe” on our software CD
6. Software Registration: copy the two *.ini files in ”Registration” folder to “C:Program Files (x86)Toyota DiagnosticsTechstreamEnv
* Attention: It’s C:Program Files (x86) not C:Program Files , BIG DIFFERENCE !!!
* Attention: It’s C:Program Files (x86) not C:Program Files , BIG DIFFERENCE !!!
Istopmotion free mac. 7. Registry Hack: Run the mvci-64bit.reg file to modify the registry for Techstream to recognize MINI-VCI under Windows x64
8. Run Techstream software. Go to Setup | VIM Select menu and select the ”XHorse – MVCI”
11. Connect Mini VCI cable to your car‘s OBDII interface, turn ignition on, then click ”Connect to Vehicle” in Techstream. Wait. Then wait again. If everything works, you will be prompted to confirm car year/model after which you’ll get to the diagnostic interface.
* Important Note:
1. DO NOT change the “User Type” when you will run your TIS Techstream for 1st time! LEAVE IT with the Default option! “Official” Dealer/Repairer with other words…
2. in [ VIM Select ] option, please select the [ Xhorse – MVCI ], not [ TIS Techstream VIM ]
3. If you get the following reminder while using the program:
—————————————————————-
Register Techstream Software (S314-03)
Network connection is unavailable. A network connection is required to use Techstream software.
You can only connect 29 more times without a network connection before software registration is required.
————————————————————--
You can reset that as following steps:
Go to C:Program FilesToyota DiagnosticsTechstreamEnv and find ”IT3usercustom.ini” file and look for ”Connectioncount=1” or what ever number of times you tried and just delete ”connectioncount=1”. Click save and you should be reseted back to 30
1. DO NOT change the “User Type” when you will run your TIS Techstream for 1st time! LEAVE IT with the Default option! “Official” Dealer/Repairer with other words…
2. in [ VIM Select ] option, please select the [ Xhorse – MVCI ], not [ TIS Techstream VIM ]
3. If you get the following reminder while using the program:
—————————————————————-
Register Techstream Software (S314-03)
Network connection is unavailable. A network connection is required to use Techstream software.
You can only connect 29 more times without a network connection before software registration is required.
————————————————————--
You can reset that as following steps:
Go to C:Program FilesToyota DiagnosticsTechstreamEnv and find ”IT3usercustom.ini” file and look for ”Connectioncount=1” or what ever number of times you tried and just delete ”connectioncount=1”. Click save and you should be reseted back to 30